12/10/07 Model LE10A Text 1 Operator’s Manual Text Section I Model LE-10A Dake/Johnson Horizontal Band saw Fully Automatic DAKE Di
12/10/07 Model LE10A Text 10CAUTION!!!!! THE GROUND WIRE MUST BE CONNECTED; FAILURE TO CONNECT THE GROUND WIRE CAN DAMAGE THE MACHINE AND VOID THE WA
12/10/07 Model LE10A Text 11 SECTION 4 4.1 Control Panel Description 1. POWER LIGHT This light will come on when the circu
12/10/07 Model LE10A Text 12 4. AUTO-MANUAL SELECTOR For Continuous cutting, turn this selector to To individually operate each function, turn thi
12/10/07 Model LE10A Text 13For bundle cutting, set this switch to the multiple picture, so that the rear vise remains at the forward limit position.
12/10/07 Model LE10A Text 14 Warning!!!!! Never change the blade with the power on. f. Remove the blade safety cover. g. Open both the drive whee
12/10/07 Model LE10A Text 15i. Carefully place the work piece onto the work feed table so that is extends approximately 2.5” (60mm) beyond the rear
12/10/07 Model LE10A Text 16 When the blade drive button is pressed, the cutting fluid pump begins to operate causing the cutting flui
12/10/07 Model LE10A Text 174.5 Automatic operation instructions AUTOMATIC OPERATION 1. Cut the edge of the work piece by using the same procedures
12/10/07 Model LE10A Text 18c. Set the feed times counter at 2. d. Now the material will be pushed forward two times, each time moving the material
12/10/07 Model LE10A Text 19 WARNING!!!!! Keep fingers clear of vise, personal injury could occur. This multi-vise is used when bundle cutting is pe
12/10/07 Model LE10A Text 2 FOREWORD This manual has been prepared to acquaint you with the operation, maintenance, and serviceable components of yo
12/10/07 Model LE10A Text 20 BLADE BREAK IN OPERATION When a new saw blade is used, be sure to first break in the blade before using it for actua
12/10/07 Model LE10A Text 21 4.8 Cutting Data
12/10/07 Model LE10A Text 226.2 Lubrication Description Lubricant Hydraulic Oil DTE 24 Hydraulic oil Gearbox Oil 80/90 Synthetic gear lube Driv
12/10/07 Model LE10A Text 23 SECTION 8 – TROUBLE SHOOTING CHART 8.1 Machine has power but will not start cut in Semi-Auto mode Vibration during cu
12/10/07 Model LE10A Text 24 8.1 Minor trouble shooting Symptom Probable Cause Corrective Action Hydraulic pump motor does not run even though hy
12/10/07 Model LE10A Text 3 CONTENTS SECTION 1 – Safety 1.1 General Safety Instructions 1.2 Location of Safety Labels SECTION 2 – Description 2.1
12/10/07 Model LE10A Text 4 2.1 General Product Specifications Machine Type Horizontal scissors type Rapid Head Approach Sure stop hydraulically cont
12/10/07 Model LE10A Text 5 SECTION 1 1.1 General Safety Instruction Read and understand the instruction manual and warning signs before operating t
12/10/07 Model LE10A Text 6 Location of Safety Labels 1.2 SAFETY
12/10/07 Model LE10A Text 7 2.2 Machine Life The intended life limit of this machine is ten years under normal operating conditions and with good ma
12/10/07 Model LE10A Text 8 LE10A Item Metric English Machine Weight W 1200 Kg 2,646 lbs Capacity, T 2 ton 2 ton Length of the Fork, L1 1.5 met
12/10/07 Model LE10A Text 9 Figure 3.4 Warning!!!! Failure to remove this bracket could cause damage to the machine and void the warranty.
Commenti su questo manuale